Open now
Veteran Owned & Operated · Licensed, Bonded & Insured · AZ ROC 350424

Home/ Blog/ Furnace repair

Furnace repair ยท Kingman · November 19, 2026

Furnace Lights Then Shuts Off? A Kingman Guide to Flame Sensors and Safety Switches

Your Kingman furnace lights, runs a few seconds or a few minutes, then shuts off and tries again. Here is what usually causes it, the safe checks you can do, and when to call for furnace repair.

(928) 565-6440

The call we hear most in Kingman right now

Once the nights in Kingman drop into the 30s, one call comes in more than almost any other: the furnace starts, you hear the burners light, and a few seconds later it shuts off. Then it tries again. After a few tries it may stop trying at all and leave the house cold. This week our technicians fixed exactly that on a Kingman furnace. The burners lit and went right back out, and the cause turned out to be the flame sensor, which was replaced and the heat came back on.

A furnace that keeps shutting off is not always a big repair. Very often it is a safety part doing its job, or a small part that has worn out.

Furnace flame sensor held in a technician's hand beside an open gas furnace during a heating service call

How long it runs before it quits tells you a lot

Pay attention to the timing before you call. It helps you and it helps us show up ready.

  • Lights, then goes out within a few seconds. This is the flame sensor pattern. The flame sensor is a thin metal rod that sits in the burner flame. Its only job is to prove to the control board that there is a flame. If the rod is coated with oxidation or dust, or the part is simply worn out, the board cannot see the flame and shuts off the gas within seconds to be safe. It will retry a few times, then lock out. A weak igniter or a low gas supply can look similar.
  • Runs for a few minutes, then shuts off with the blower still running. That usually points to a safety switch. A high-limit switch trips when the furnace overheats, and overheating almost always means poor airflow: a packed filter, a dirty blower wheel, or too many closed vents. A pressure switch trips when the venting or the inducer motor is not moving combustion gases out the way it should.
  • Heats the house, but turns on and off every few minutes all day. That is short cycling. It can be a thermostat in a bad spot, such as near a supply vent or in direct sun, a furnace that is far larger than the house needs, or one of the safety switches above tripping and resetting over and over.
  • Runs, shuts off, and the control board light is blinking a pattern. Most modern furnaces have a small window in the lower door where an LED flashes a code. Count the flashes and match them to the chart on the inside of the door. Write it down for the technician.

Why Kingman furnaces do this in the first cold weeks

Kingman sits around 3,300 feet. Afternoons can still feel mild in November while nights drop near freezing, so a furnace goes months without running and then suddenly starts cycling many times a day. Dust is the other half. Wind carries fine desert dust into return grilles, filters and burner compartments all year, and it settles on burners and the flame sensor while the furnace sits idle all summer. That is why the first cold week brings so many of these calls at once.

Close-up of a furnace burner and heat exchanger inlet with heat discoloration during an inspection

Safe checks you can do before you call

If you smell gas, or rotten eggs, stop here. Leave the house, do not flip switches, and call the gas utility from outside. Then call us. Otherwise, these checks are safe and do not involve opening the burner compartment:

  1. Check the filter. If it is gray and packed, replace it. A clogged filter is the most common reason a furnace overheats and shuts itself off after a few minutes.
  2. Open the vents. Make sure supply registers and return grilles are open and not blocked by furniture, rugs or boxes.
  3. Look at the thermostat. Make sure it is set to Heat, the setpoint is a few degrees above room temperature, and replace the batteries if it has them.
  4. Check the outside vent pipes. On high-efficiency furnaces, look at the PVC intake and exhaust pipes outside. A bird nest, weeds or a tumbleweed can block them and trip the pressure switch.
  5. Read the code, then reset once. Count the LED flashes through the door window. Then turn the furnace switch off for a minute and back on. If it locks out again, leave it off and call.

We do not recommend pulling and sanding a flame sensor yourself. It means opening the burner compartment, the part is easy to crack, and a sensor that is worn out will keep failing even after it is cleaned. A sensor that comes back after cleaning is often only a short fix, which is why our technicians replace it when testing shows it is done.

When to call for furnace repair

Call us if the furnace locks out again after one reset, if a breaker trips, if you hear loud banging when the burners light, if you see scorch marks or melted wires, or if the house is losing heat on a cold night. If you have a heat pump instead of a gas furnace, our guide to a heat pump blowing cold air covers that side. If the furnace will not start at all, see what to check when a furnace won't turn on in Kingman.

When you call, you get the service call price on the phone before anyone heads your way, and the diagnostic is credited toward the repair when you approve it. On site, the technician reads the code, tests the flame signal, checks the igniter, gas pressure, pressure switch, limit switch, venting and airflow, and shows you what failed. Nothing gets replaced without your OK. Flame sensors, igniters and pressure switches are common parts, so many of these repairs are finished in one visit. Our furnace repair page covers the rest of what we fix.

Repair it, or is it time to replace?

A flame sensor or a switch is a repair, not a reason to replace a furnace. If the furnace is older and the inspection turns up a cracked heat exchanger, a failing inducer or a string of repairs stacking up, we will tell you straight and lay out repair and replacement side by side with no pressure to decide that day. Replacement estimates are free. As a Trane Comfort Specialist we install Trane gas furnaces sized for your home, and financing is available on approved credit.

Trane gas furnace installed in an attic with gas piping and an Air-Exx service sticker on the cabinet

Head it off with a tune-up

Most of the shut-off calls we run in the first cold weeks are things a tune-up catches early: a coated flame sensor, a weak igniter, dirty burners, a clogged filter or a pressure switch tube full of debris. Our seasonal tune-up is $79, limited time $69 through December 31, 2026. Our post on what a fall furnace tune-up checks walks through the full list, and our maintenance plans schedule the visits for you with priority scheduling when something does go wrong.

Common questions

Why does my furnace light and then shut off after a few seconds? The most common cause is a dirty or worn flame sensor. The burners light, but the control board cannot confirm the flame, so it shuts off the gas to be safe and tries again. A weak igniter or low gas supply can cause the same pattern.

Is it safe to keep resetting my furnace? One reset is fine. If it locks out again, leave it off and call. Repeated resets can mean gas is being sent to burners that are not lighting properly, and the safety lockout is there for a reason.

Can I clean the flame sensor myself? We do not recommend it. It means opening the burner compartment, the ceramic is easy to crack, and a worn sensor will keep failing even after cleaning. Our technicians test the flame signal and clean or replace the sensor based on the reading.

Why does my furnace run a few minutes and then shut off? That usually means a safety switch tripped. Overheating from a clogged filter, a dirty blower or closed vents trips the high-limit switch. A blocked vent pipe or a failing inducer motor trips the pressure switch. Check the filter and vents first.

How much does a furnace tune-up cost in Kingman? Our seasonal tune-up is $79, limited time $69 through December 31, 2026. For repairs, you get the service call price on the phone before we head your way, and the diagnostic is credited toward the repair when you approve it.

Air-Exx Heating Cooling and Ventilation LLC is a veteran-owned heating and cooling company serving Kingman, Golden Valley and the rest of Mohave County, plus Yavapai County. A live person answers 24 hours a day, Monday through Saturday. Furnace lighting and then shutting off? Call (928) 565-6440 or text (928) 227-8441 to book furnace repair in Kingman.

Straight answers, no surprises

You'll know the price before we start.

You get the service call price on the phone, before anyone heads your way. The diagnostic is credited toward the repair when you approve it.

(928) 565-6440 Request a Quote